[4910-13-P]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2024-0763; Project Identifier AD-2023-00924-E; Amendment 3922785; AD 2024-14-04]
RIN 2120-AA64
Airworthiness Directives; International Aero Engines, LLC
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all
International Aero Engines, LLC (IAE LLC) Model PW1122G-JM, PW1124G1-JM,
PW1124G-JM, PW1127G1-JM, PW1127G1A-JM, PW1127G1B-JM, PW1127G-JM,
PW1127GA-JM, PW1129G-JM, PW1130G-JM, PW1133G-JM, and PW1133GA-JM
engines. This AD was prompted by an in-flight shutdown (IFSD) caused by the fracture
of a low-pressure compressor (LPC) 1st-stage integrally bladed rotor (IBR-1). This AD
requires removal and replacement of affected LPC key washers and affected LPC IBR-1
and installation of inlet guide vane (IGV) spacers. The FAA is issuing this AD to address
the unsafe condition on these products.
DATES: This AD is effective [INSERT DATE 35 DAYS AFTER DATE OF
PUBLICATION IN THE FEDERAL REGISTER].
ADDRESSES:
AD Docket: You may examine the AD docket at regulations.gov under Docket No. FAA2024-0763; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday
through Friday, except Federal holidays. The AD docket contains this final rule, any
comments received, and other information. The address for Docket Operations is U.S.
Department of Transportation, Docket Operations, M-30, West Building Ground Floor,
Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.

FOR FURTHER INFORMATION CONTACT: Carol Nguyen, Aviation Safety
Engineer, FAA, 2200 South 216th Street, Des Moines, WA 98198; phone: (781) 2387655; email: carol.nguyen@faa.gov.
SUPPLEMENTARY INFORMATION:
Background
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part
39 by adding an AD that would apply to all IAE LLC Model PW1122G-JM, PW1124G1JM, PW1124G-JM, PW1127G1-JM, PW1127G1A-JM, PW1127G1B-JM, PW1127GJM, PW1127GA-JM, PW1129G-JM, PW1130G-JM, PW1133G-JM, and PW1133GAJM engines. The NPRM published in the Federal Register on March 25, 2024 (89 FR
20551). The NPRM was prompted by an incident involving an Airbus Model A320neo
airplane powered by IAE LLC Model PW1127G-JM engines that experienced an IFSD.
A manufacturer investigation determined that the IFSD was caused by a fractured LPC
IBR-1, which resulted from an aerodynamic excitation. The most likely cause of the
aerodynamic excitation was a misaligned IGV located directly upstream of the IBR-1. As
a result, Pratt & Whitney (PW) redesigned the LPC IGV arm assembly by adding a
spacer to provide additional torque capability and to prevent a misaligned vane. PW also
redesigned the IBR-1 to better withstand an aerodynamic excitation from a misaligned
IGV. In the NPRM, the FAA proposed to require removal and replacement of affected
LPC key washers and affected LPC IBR-1 and installation of LPC IGV spacers. The
FAA is issuing this AD to address the unsafe condition on these products.
Discussion of Final Airworthiness Directive
Comments
The FAA received comments from four commenters. The commenters were the
Air Line Pilots Association, International (ALPA), All Nippon Airways CO., LTD.
(ANA), Delta Air Lines, Inc (DAL), and Frontier Airlines (Frontier). ALPA supported
the NPRM without change. The following presents the comments received on the NPRM
and the FAA’s response to each comment.

Request to Update Paragraph (g)(1)
Frontier requested that the FAA update paragraph (g)(1) of the proposed AD to
read as follows: “For engines that are pre-PW Service Bulletin (SB) PW1000G-C-72-000180-00A-930A-D, Issue No. 001, dated October 10, 2020 (PW SB PW1000G-C-72-000180-00A-930A-D) with installed LPC key washers having P/N 5375416, at the next
engine shop visit after the effective date of this AD, remove the affected LPC key
washers and replace them with LPC key washers and LPC IGV spacers that are eligible
for installation.” Frontier noted that tracking installed washers on engines is very difficult
since they are not tracked parts, and post service bulletin engines have LPC key washers
and LPT IGV spacers that are eligible for installation.
The FAA agrees to update paragraph (g)(1) of this AD to include reference to
engines that have not incorporated PW SB PW1000G-C-72-00-0180-00A-930A-D.
Request to Update Paragraph (g)(2)
Frontier requested that the FAA update paragraph (g)(2) of the proposed AD to
read as follows: “For engines that are pre-service bulletin SB PW1000G-C-72-00-018900A-930A-D, with an installed LPC IBR-1 having PN 5373831, at the next piece-part
exposure after effective date of this AD, remove the affected LPC IBR-1 and replace with
an LPC IBR-1 eligible for installation.”
The FAA disagrees with the request because the LPC IBR-1 is a tracked lifelimited part, so adding qualifying language for “pre-PW SB PW1000G-C-72-00-018900A-930A-D” engines is unnecessary. The FAA did not change this AD as a result of this
comment.
Request to Add “Credit for Previous Actions” Paragraph
DAL requested that the FAA add a “Credit for Previous Actions” paragraph to the
proposed AD to allow credit for the actions required by paragraph (g)(1) if PW SB
PW1000G-C-72-00-0180-00A-930A-D was previously accomplished. ANA also
requested that accomplishment of PW SB PW1000G-C-72-00-0180-00A-930A-D be
accepted as credit for paragraph (g)(1) of the proposed AD, and accomplishment of PW
SB PW1000G-C-72-00-0189-00A-930A, Issue 001, dated January 26, 2022, PW SB
PW1000G-C-72-00-0189-00A-930A, Issue 002, dated March 15, 2022, and PW SB

PW1000G-C-72-00-0189-00A-930A, Issue 003, dated November 28, 2022, be accepted
as credit for paragraph (g)(2) of the proposed AD if these actions were performed before
the effective date of the proposed AD. DAL noted that because the proposed AD does not
provide credit for installing the post-SB spacers and washers, operators must physically
verify that all 61 spacers are present and all 61 washers are post-SB on all engines,
regardless of whether or not the engine records show accomplishment of PW SB
PW1000G-C-72-00-0180-00A-930A-D. DAL also noted that this is a very manual, timeintensive task that should be avoided considering PW SB PW1000G-C-72-00-0180-00A930A-D installs key washers P/N 5375416 and LPC spacers P/N 5375433, and those
parts comply with the “part eligible for installation” definitions listed in paragraphs (h)(3)
and (h)(4) of the proposed AD.
The FAA disagrees with the request to add a “Credit for Previous Actions”
paragraph to this AD. This AD references affected engines with specific P/Ns installed in
paragraph (g) of this AD, and if the service bulletins related to this AD have already been
performed on the engine, then the affected P/Ns are no longer installed and the AD is no
longer applicable to those engines. Therefore, previous credit is not necessary because the
engine no longer has an affected P/N installed. The FAA notes that paragraph (g)(1) of
this AD has been changed to reference PW SB PW1000G-C-72-00-0180-00A-930A-D
and to reduce the burden on operators. The FAA did not change this AD as a result of this
comment.
Request to Clarify Meaning of “At the Next Piece-Part Exposure”
ANA requested that the FAA clarify the meaning of “at the next piece-part
exposure” in paragraph (g)(2) of the proposed AD. ANA asks if LPC IBR-1 is already
separated from the LPC module and assembly has already begun by the effective date of
this AD, should the requirement of paragraph (g)(2) not be performed in this shop visit?
ANA also wondered about the same scenario if the assembly had not begun by the
effective date of this AD.
To clarify, the FAA’s meaning of “at the next piece-part exposure” covers both
cases. Paragraph (h)(2) of this AD defines a “piece-part exposure” as when the LPC IBR1 is separated from the LPC module. The FAA considers the “next” exposure to include

any separation of the LPC IBR-1 from the LPC module after the effective date of this
AD. If the LPC IBR-1 is assembled into the module on the effective date of this AD, then
it is not a “piece-part exposure.” If the LPC IBR-1 is separated from the LPC module
after the effective date of the AD, then paragraph (g)(2) of this AD will need to be
performed because it will meet the definition of “piece-part exposure”. The FAA is not
concerned if the assembly of the LPC module has started or not.
The FAA did not change this AD as a result of this comment.
Request to Clarify “Major Mating Engine Flanges”
ANA requested that the FAA clarify if “major mating engine flanges” referenced
in paragraph (h)(1) of the proposed AD are considered as flanges E through P.
To clarify, the FAA considers the major mating engine flanges referenced in
paragraph (h)(1) of this AD as flanges E through P, inclusive. The FAA did not change
this AD as a result of this comment.
Request to Clarify “Induction of an Engine”
ANA requested that the FAA clarify the meaning of “induction of an engine” in
paragraph (h)(1) of the proposed AD. ANA asked if an engine is already in-shop for
maintenance involving the separation of pairs of major mating engine flanges at the
effective date of this AD, does paragraph (g)(1) need to be performed in this shop visit?
To clarify, the FAA’s meaning of “induction of an engine” when using the
example provided by ANA is: “if the engine was already at an engine shop visit on the
effective date of this AD, the requirements of paragraph (g)(1) would apply at the next
engine shop visit after the effective date of this AD.” The FAA did not change this AD as
a result of this comment.
Conclusion
The FAA reviewed the relevant data, considered any comments received, and
determined that air safety requires adopting this AD as proposed. Accordingly, the FAA
is issuing this AD to address the unsafe condition on these products. Except for minor
editorial changes, and any other changes described previously, this AD is adopted as
proposed in the NPRM. None of the changes will increase the economic burden on any
operator.

Costs of Compliance
The FAA estimates that this AD affects 215 engines installed on airplanes of U.S.
registry.
The FAA estimates the following costs to comply with this AD:
Estimated costs
Action

Labor Cost

Parts Cost

Replace LPC
IBR-1

1 work-hours x
$85 per hour =
$85
20 work-hours
x $85 per hour
= $1,700

Replace IGV
key washers
and install IGV
spacers

$36,350

Cost per
product
$36,435

Cost on U.S.
operators
$7,833,525

$4,392

$6,092

$1,309,780

Authority for this Rulemaking
Title 49 of the United States Code specifies the FAA’s authority to issue rules on
aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator.
Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency’s
authority.
The FAA is issuing this rulemaking under the authority described in Subtitle VII,
Part A, Subpart III, Section 44701: General requirements. Under that section, Congress
charges the FAA with promoting safe flight of civil aircraft in air commerce by
prescribing regulations for practices, methods, and procedures the Administrator finds
necessary for safety in air commerce. This regulation is within the scope of that authority
because it addresses an unsafe condition that is likely to exist or develop on products
identified in this rulemaking action.
Regulatory Findings
This AD will not have federalism implications under Executive Order 13132. This
AD will not have a substantial direct effect on the States, on the relationship between the
national government and the States, or on the distribution of power and responsibilities
among the various levels of government.
For the reasons discussed above, I certify that this AD:

(1) Is not a “significant regulatory action” under Executive Order 12866,
(2) Will not affect intrastate aviation in Alaska, and
(3) Will not have a significant economic impact, positive or negative, on a
substantial number of small entities under the criteria of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.
The Amendment
Accordingly, under the authority delegated to me by the Administrator, the FAA
amends 14 CFR part 39 as follows:
PART 39 - AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
§ 39.13 [Amended]
2. The FAA amends § 39.13 by adding the following new airworthiness directive:
2024-14-04 International Aero Engines, LLC: Amendment 39-22785; Docket
No. FAA-2024-0763; Project Identifier AD-2023-00924-E.
(a) Effective Date
This airworthiness directive (AD) is effective [INSERT DATE 35 DAYS AFTER
DATE OF PUBLICATION IN THE FEDERAL REGISTER].
(b) Affected ADs
None.
(c) Applicability
This AD applies to International Aero Engines Model PW1122G-JM,
PW1124G1-JM, PW1124G-JM, PW1127G1-JM, PW1127G1A-JM, PW1127G1B-JM,
PW1127G-JM, PW1127GA-JM, PW1129G-JM, PW1130G-JM, PW1133G-JM, and
PW1133GA-JM engines.
(d) Subject
Joint Aircraft System Component (JASC) Code 7230, Turbine Engine
Compressor Section.
(e) Unsafe Condition

This AD was prompted by an in-flight shutdown caused by the fracture of a lowpressure compressor (LPC) 1st-stage integrally bladed rotor (IBR-1). The FAA is issuing
this AD to prevent the failure of the LPC IBR-1. The unsafe condition, if not addressed,
could result in damage to the engine, damage to the airplane, and possible loss of the
airplane.
(f) Compliance
Comply with this AD within the compliance times specified, unless already done.
(g) Required Actions
(1) For affected engines that have not incorporated Pratt & Whitney Service
Bulletin PW1000G-C-72-00-0180-00A-930A-D (initial issue or any revision), and with
installed LPC key washers having part number (P/N) 5375416, at the next engine shop
visit after the effective date of this AD, remove the affected LPC key washers and replace
them with LPC key washers and LPC inlet guide vane (IGV) spacers that are eligible for
installation.
(2) For affected engines with an installed LPC IBR-1 having P/N 5373831, at the
next piece-part exposure after the effective date of this AD, remove the affected LPC
IBR-1 and replace with an LPC IBR-1 eligible for installation.
(h) Definitions
For the purposes of this AD:
(1) An “engine shop visit” is the induction of an engine into the shop for
maintenance involving the separation of pairs of major mating engine flanges, except that
the separation of engine flanges solely for the purposes of transportation without
subsequent engine maintenance does not constitute an engine shop visit.
(2) A “piece-part exposure” is when the LPC IBR-1 is separated from the LPC
module.
(3) “LPC key washers eligible for installation” are any LPC key washers having
P/N 5375434 or later-approved P/N.
(4) “LPC IGV spacers eligible for installation” are any LPC IGV spacers having
P/N 5375433 or later-approved P/N.

(5) An “LPC IBR-1 eligible for installation” is any LPC IBR-1 having P/N
5373841 or later-approved P/N.
(i) Alternative Methods of Compliance (AMOCs)
(1) The Manager, AIR-520 Continued Operational Safety Branch, FAA, has the
authority to approve AMOCs for this AD, if requested using the procedures found in 14
CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal
inspector or local Flight Standards District Office, as appropriate. If sending information
directly to the manager of AIR-520 Continued Operational Safety Branch, send it to the
attention of the person identified in paragraph (j) of this AD and email to:
AMOC@faa.gov.
(2) Before using any approved AMOC, notify your appropriate principal
inspector, or lacking a principal inspector, the manager of the local flight standards
district office/certificate holding district office.
(j) Additional Information
For more information about this AD, contact Carol Nguyen, Aviation Safety
Engineer, FAA, 2200 South 216th Street, Des Moines, WA 98198; phone: (781) 2387655; email: carol.nguyen@faa.gov.
(k) Material Incorporated by Reference
None.
Issued on July 10, 2024.

Peter A. White,
Deputy Director, Integrated Certificate Management Division,
Aircraft Certification Service.
[FR Doc. 2024-15466 Filed: 7/15/2024 8:45 am; Publication Date: 7/16/2024]